Danfoss VLT HVAC Basic Drive FC 101 Informações Técnicas Página 40
- Página / 99
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
5-40 Function Relay
Array (Relay 1 [0], Relay 2 [1])
Select options to define the function of the relays.
The selection of each mechanical relay is realised in an array
parameter.
Option: Function:
[24] Ready, Voltage
OK
Frequency converter is ready for
operation and mains voltage is within
specified voltage range.
[25] Reverse Motor runs/is ready to run clockwise
when logic = 0 and counter clockwise
when logic = 1. Output changes as soon
as reversing signal is applied.
[26] Bus OK Active communication (no time-out) via
serial communication port.
[35] External Interlock See digital input.
[36] Control word bit
11
Bit 11 in control word controls relay.
[37] Control word bit
12
Bit 12 in control word controls relay.
[45] Bus Control
[60] Comparator 0 See parameter group 13-1*. If Comparator
0 is evaluated as TRUE, the output will go
high. Otherwise, it will be low.
[61] Comparator 1 See parameter group 13-1*. If Comparator
2 is evaluated as TRUE, the output will go
high. Otherwise, it will be low.
[62] Comparator 2 See parameter group 13-1*. If Comparator
2 is evaluated as TRUE, the output will go
high. Otherwise, it will be low.
[63] Comparator 3 See parameter group 13-1*. If Comparator
3 is evaluated as TRUE, the output will go
high. Otherwise, it will be low.
[64] Comparator 4 See parameter group 13-1*. If Comparator
4 is evaluated as TRUE, the output will go
high. Otherwise, it will be low.
[65] Comparator 5 See parameter group 13-1*. If Comparator
5 is evaluated as TRUE, the output will go
high. Otherwise, it will be low.
[70] Logic rule 0 See parameter group 13-4*. If Logic Rule
0 is evaluated as TRUE, the output will go
high. Otherwise, it will be low.
[71] Logic rule 1 See parameter group 13-4*. If Logic Rule
1 is evaluated as TRUE, the output will go
high. Otherwise, it will be low.
[72] Logic rule 2 See parameter group 13-4*. If Logic Rule
2 is evaluated as TRUE, the output will go
high. Otherwise, it will be low.
[73] Logic rule 3 See parameter group 13-4*. If Logic Rule
3 is evaluated as TRUE, the output will go
high. Otherwise, it will be low.
5-40 Function Relay
Array (Relay 1 [0], Relay 2 [1])
Select options to define the function of the relays.
The selection of each mechanical relay is realised in an array
parameter.
Option: Function:
[74] Logic rule 4 See parameter group 13-4*. If Logic Rule
4 is evaluated as TRUE, the output will go
high. Otherwise, it will be low.
[75] Logic rule 5 See parameter group 13-4*. If Logic Rule
5 is evaluated as TRUE, the output will go
high. Otherwise, it will be low.
[80] SL digital output
A
See 13-52 SL Controller Action. The input
will go high whenever the Smart Logic
Action [38] Set dig. out. A high is executed.
The input will go low whenever the Smart
Logic Action [32] Set dig. out. A low is
executed.
[81] SL digital output
B
See 13-52 SL Controller Action. The input
will go high whenever the Smart Logic
Action [39] Set dig. out. Bhigh is executed.
The input will go low whenever the Smart
Logic Action [33] Set dig. out. B low is
executed.
[82] SL digital output
C
See 13-52 SL Controller Action. The input
will go high whenever the Smart Logic
Action [40] Set dig. out. C high is executed.
The input will go low whenever the Smart
Logic Action [34] Set dig. out. C low is
executed.
[83] SL digital output
D
See 13-52 SL Controller Action. The input
will go high whenever the Smart Logic
Action [41] Set dig. out. D high is
executed. The input will go low whenever
the Smart Logic Action [35] Set dig. out. D
low is executed.
[160] No alarm The output is high when no alarm is
present.
[161] Running reverse The output is high when the frequency
converter is running counter clockwise
(the logical product of the status bits
‘running’ AND ‘reverse’).
[165] Local ref. active
The output is high when 3-13 Reference
Site = [2] Local or when 3-13 Reference Site
= [0] Linked to hand auto at the same time
as the LCP is in [Hand on] mode.
[166] Remote ref.
active
The output is high when 3-13 Reference
Site [1] or Linked to hand/auto [0] while
the LCP is in [Auto on] mode.
[167] Start command
activ
The output is high when there is an active
Start command (i.e. via digital input bus
connection or [Hand on] or [Auto on], and
no Stop command is active.
Parameters VLT HVAC Basic Drive Programming Guide
MG.18.B1.02 - VLT
®
is a registered Danfoss trademark 39
3
3
- Programming Guide 1
- 1 Introduction 2
- 3 Parameters 2
- Contents 2
- 2 MG.18.B1.02 - VLT 3
- 4 Troubleshooting 4
- 5 Parameter Lists 4
- 4 MG.18.B1.02 - VLT 5
- 1.1.2 Symbols 7
- 1.1.3 Abbreviations 7
- Definitions 8
- 175ZA078.10 9
- Pull-out 9
- MG.18.B1.02 - VLT 10
- High Voltage 11
- 1.1.6 Electrical Overview 12
- 2 How to Programme 13
- 14 MG.18.B1.02 - VLT 15
- Closed Loop Set-up Wizard 17
- Main Menu 19
- * English 21
- * Interna 21
- * Active Set 22
- 3.1.3 0-3* LCP Custom Readout 23
- 3.1.4 0-4* LCP 24
- 3.1.5 0-5* Copy / Save 24
- 3.1.6 0-6* Password 24
- * Variable 25
- * [0.01 - 26.0 26
- * [100.0 26
- * Off No function 26
- 3.2.3 1-3* Adv. Motor Data 27
- 1-4* Cable Length 27
- 3.2.7 1-7* Start Adjustments 28
- 3.2.8 1-8* Stop Adjustments 29
- 3.2.9 1-9* Motor Temperature 29
- 3.4.1 3-0* Reference Limits 31
- 3.4.2 3-1* References 31
- * Analog in 54 32
- * Local bus 32
- * [0.05 32
- 3.4.5 3-8* Other Ramps 33
- 3.5.1 4-1* Motor Limits 34
- 3.5.2 4-5* Adj. Warnings 34
- 3.5.3 4-6* Speed Bypass 35
- 3.6.1 5-0* Digital I/O Mode 36
- 3.6.2 5-1* Digital Inputs 36
- * No operation 38
- * Coast inverse 38
- 3.6.3 5-4* Relays 39
- 5-40 Function Relay 40
- Option: Function: 40
- 3.6.4 5-9* Bus Controlled 41
- 3.7.1 6-0* Analog I/O Mode 42
- 3.7.2 6-1* Analog Input 53 42
- 3.7.3 6-2* Analog Input 54 43
- * [0.0 - 200.0 44
- * [0.0 - 100.0 %] 44
- * 0-20 mA 45
- Options - Group 8 47
- 3.8.1 8-0* General Settings 47
- 3.8.2 8-3* FC Port Settings 47
- 3.8.3 8-5* Digital/Bus 48
- 3.8.4 8-7* BACnet 49
- 3.8.6 8-9* Bus Feedback 50
- 3.9.1 13-** Prog. Features 51
- 13-0* SLC Settings 51
- * Do not reset 53
- * Disabled 53
- * [-9999.0 54
- * [0.0 54
- 13-52 SL Controller Action 58
- * Manual reset 59
- 3.10.4 14-4*Energy Optimising 60
- 3.10.5 14-5* Environment 60
- * [1.0 - 16.0 kHz] 61
- 3.11.1 15-0* Operating Data 62
- 3.11.2 15-3* Alarm Log 62
- 3.12.1 16-0* General Status 64
- 3.12.2 16-1* Motor Status 64
- 3.12.3 16-3* Drive Status 65
- * [0.1 - 9999.0 69
- * [0.0 - 400.0 %] 69
- * [0.0 - 400.0 Hz] 70
- * [0.0 - 100.0 70
- Group 24 72
- 3.16.1 24-0* Fire Mode 72
- Range: Function: 74
- 4.1.1 Alarm Words 77
- 4.1.2 Warning Words 77
- 4.1.3 Extended Status Words 78
- 4.1.4 Fault Messages 78
- 78 MG.18.B1.02 - VLT 79
- 5.1.3 1-** Load and Motor 83
- 5.1.4 2-** Brakes 84
- 5.1.5 3-** Reference/Ramps 84
- 5.1.6 4-** Limits/Warnings 85
- 5.1.7 5-** Digital In/Out 85
- 5.1.8 6-** Analog In/Out 86
- 5.1.9 8-** Comm. and Options 87
- 5.1.10 13-** Smart Logic 88
- 5.1.13 16-** Data Readouts 90
- 5.1.16 22-** Appl. Functions 91
- 92 MG.18.B1.02 - VLT 93
- 94 MG.18.B1.02 - VLT 95
- 96 MG.18.B1.02 - VLT 97
- *MG18B102* 98
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.050 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais