Danfoss 102 Instruções de Operação Página 56
- Página / 74
- Índice
- RESOLUÇÃO DE PROBLEMAS
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
Max. load GND - analog output 500 Ω
Accuracy on analog output Max. error: 0.5% of full scale
Resolution on analog output 12 bit
The analog output is galvanically isolated from the supply voltage (PELV) and other high-voltage terminals.
Control card, RS-485 serial communication
Terminal number 68 (P,TX+, RX+), 69 (N,TX-, RX-)
Terminal number 61 Common for terminals 68 and 69
The RS-485 serial communication circuit is functionally separated from other central circuits and galvanically isolated from the
supply voltage (PELV).
Digital output
Programmable digital/pulse outputs 2
Terminal number 27, 29
1)
Voltage level at digital/frequency output 0-24 V
Max. output current (sink or source) 40 mA
Max. load at frequency output 1 kΩ
Max. capacitive load at frequency output 10 nF
Minimum output frequency at frequency output 0 Hz
Maximum output frequency at frequency output 32 kHz
Accuracy of frequency output Max. error: 0.1 % of full scale
Resolution of frequency outputs 12 bit
1)
Terminal 27 and 29 can also be programmed as input.
The digital output is galvanically isolated from the supply voltage (PELV) and other high-voltage terminals.
Control card, 24 V DC output
Terminal number 12, 13
Output voltage 24 V +1, -3 V
Max. load 200 mA
The 24 V DC supply is galvanically isolated from the supply voltage (PELV), but has the same potential as the analog and digital
inputs and outputs.
Relay outputs
Programmable relay outputs 2
Relay 01 Terminal number 1-3 (break), 1-2 (make)
Max. terminal load (AC-1)
1)
on 1-3 (NC), 1-2 (NO) (Resistive load) 240 V AC, 2 A
Max. terminal load (AC-15)
1)
(Inductive load @ cosφ 0.4) 240 V AC, 0.2 A
Max. terminal load (DC-1)
1)
on 1-2 (NO), 1-3 (NC) (Resistive load) 60 V DC, 1 A
Max. terminal load (DC-13)
1)
(Inductive load) 24 V DC, 0.1 A
Relay 02 (FC 302 only) Terminal number 4-6 (break), 4-5 (make)
Max. terminal load (AC-1)
1)
on 4-5 (NO) (Resistive load)
2)3)
Overvoltage cat. II 400 V AC, 2 A
Max. terminal load (AC-15)
1)
on 4-5 (NO) (Inductive load @ cosφ 0.4) 240 V AC, 0.2 A
Max. terminal load (DC-1)
1)
on 4-5 (NO) (Resistive load) 80 V DC, 2 A
Max. terminal load (DC-13)
1)
on 4-5 (NO) (Inductive load) 24 V DC, 0.1 A
Max. terminal load (AC-1)
1)
on 4-6 (NC) (Resistive load) 240 V AC, 2 A
Max. terminal load (AC-15)
1)
on 4-6 (NC) (Inductive load @ cosφ 0.4) 240 V AC, 0.2 A
Max. terminal load (DC-1)
1)
on 4-6 (NC) (Resistive load) 50 V DC, 2 A
Max. terminal load (DC-13)
1)
on 4-6 (NC) (Inductive load) 24 V DC, 0.1 A
Min. terminal load on 1-3 (NC), 1-2 (NO), 4-6 (NC), 4-5 (NO) 24 V DC 10 mA, 24 V AC 20 mA
Environment according to EN 60664-1 overvoltage category III/pollution degree 2
1)
IEC 60947 part 4 and 5
The relay contacts are galvanically isolated from the rest of the circuit by reinforced isolation (PELV).
2)
Overvoltage Category II
3)
UL applications 300 V AC 2A
Specifications
VLT
®
HVAC Drive Operating Instructions
54 MG11AJ02 - Rev. 2013-07-31
88
- Operating Instructions 1
- HVAC Drive FC 102 1
- Contents 3
- 6 Application Set-up Examples 4
- 8 Specifications 4
- 9 Appendix 4
- 1 Introduction 5
- 2 Safety 7
- EQUIPMENT HAZARD! 8
- WINDMILLING! 8
- INTERNAL FAILURE! 8
- Type 12 / IP55 Tamb.45 9
- 3.1.3 Product Overview 10
- Mechanical Installation 11
- 130BD528.10 12
- 130BD504.10 12
- 4 Electrical Installation 13
- 4.4 Wiring Schematic 14
- EMC INTERFERENCE! 15
- 130BT248.10 16
- 130BT334.10 16
- 4.7 AC Mains Connection 17
- 4.8 Control Wiring 18
- Control Terminal Types 18
- 130BD546.10 19
- 130BD530.10 20
- 5 Commissioning 23
- 2605 kWh 24
- Basic Programming 26
- Asynchronous Motor Setup 27
- Permanent Magnet Motor Setup 27
- 5.5 Checking Motor Rotation 29
- 5.6 Local-control Test 29
- 5.7 System Start-up 29
- Maintenance 29
- 6.1 Application Examples 30
- 6.1.1 Speed 30
- Start/Stop 31
- Application Set-up Examples 32
- 6.1.4 RS-485 33
- Motor Thermistor 33
- 7.1 Status Messages 34
- 130BP086.11 36
- 36 MG11AJ02 - Rev. 2013-07-31 38
- MG11AJ02 - Rev. 2013-07-31 37 39
- MG11AJ02 - Rev. 2013-07-31 39 41
- 40 MG11AJ02 - Rev. 2013-07-31 42
- 7.4 Troubleshooting 43
- Specifications 46
- 8.2 Mains Supply 53
- 8.4 Ambient Conditions 53
- 52 MG11AJ02 - Rev. 2013-07-31 54
- MG11AJ02 - Rev. 2013-07-31 53 55
- 54 MG11AJ02 - Rev. 2013-07-31 56
- Connection Tightening Torques 57
- 8.8 Fuse Specifications 58
- 8.8.1 CE Compliance 58
- 380-480 V 59
- 525-600 V 59
- UL Compliance 60
- 3x525-600 V 62
- 3x525-690 V 63
- Appendix 66
- 68 MG11AJ02 - Rev. 2013-07-31 70
- MG11AJ02 - Rev. 2013-07-31 69 71
- 70 MG11AJ02 - Rev. 2013-07-31 72
- MG11AJ02 - Rev. 2013-07-31 71 73
- *MG11AJ02* 74
Manuais e produtos relacionados com Adaptadores e conversores de corrente Danfoss 102
(28 páginas)
(1 páginas)© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.025 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais