Danfoss 102 Instruções de Operação Página 26
- Página / 74
- Índice
- RESOLUÇÃO DE PROBLEMAS
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
Recommended Initialisation Procedure, via
14-22 Operation Mode
1. Press [Main Menu] twice to access parameters.
2.
Scroll to 14-22 Operation Mode and press [OK].
3.
Scroll to Initialisation and press [OK].
4. Remove power to the unit and wait for the
display to turn off.
5. Apply power to the unit.
Default parameter settings are restored during start-up.
This may take slightly longer than normal.
6. Alarm 80 is displayed.
7. Press [Reset] to return to operation mode.
Manual Initialisation Procedure
1. Remove power to the unit and wait for the
display to turn off.
2. Press and hold [Status], [Main Menu], and [OK] at
the same time while applying power to the unit
(approximately 5 s or until audible click and fan
starts).
Factory default parameter settings are restored during
start-up. This may take slightly longer than normal.
Manual initialisation does not reset the following frequency
converter information
•
15-00 Operating hours
•
15-03 Power Up's
•
15-04 Over Temp's
•
15-05 Over Volt's
5.4
Basic Programming
5.4.1 Commissioning with SmartStart
The SmartStart wizard enables fast configuration of basic
motor and application parameters.
•
At first power up or after initialisation of the
frequency converter, SmartStart starts by itself.
•
Follow on-screen instructions to complete
commssioning of the frequency converter.
SmartStart can always be re-activiated by
selecting Quick Menu Q4 - SmartStart.
•
For commissioning without use of the SmartStart
wizard, refer to 5.4.2 Commissioning via [Main
Menu] or the Programming Guide.
NOTICE
Motor data are required for the SmartStart setup. The
required data are normally available on the motor
nameplate.
5.4.2 Commissioning via [Main Menu]
Recommended parameter settings are intended for start-
up and checkout purposes. Application settings may vary.
Enter data with power ON, but before operating the
frequency converter.
1. Press [Main Menu] on the LCP.
2. Use the navigation keys to scroll to parameter
group 0-** Operation/Display and press [OK].
130BP066.10
1107 RPM
0 -
**
Operation/Display
1 -
**
Load/Motor
2 -
**
Brakes
3 -
**
Reference / Ramps
3.84 A 1 (1)
Main menu
Illustration 5.2 Main Menu
3. Use navigation keys to scroll to parameter group
0-0* Basic Settings and press [OK].
0-
**
Operation / Display
0.0%
0-0
*
Basic Settings
0-1
*
Set-up Opperations
0-2
*
LCP Display
0-3
*
LCP Custom Readout
0.00A 1(1)
130BP087.10
Illustration 5.3 Operation/Display
4.
Use navigation keys to scroll to 0-03 Regional
Settings and press [OK].
0-0
*
Basic Settings
0.0%
0-03 Regional Settings
[0] International
0.00A 1(1)
130BP088.10
Illustration 5.4 Basic Settings
5.
Use navigation keys to select [0] International or
[1] North America as appropriate and press [OK].
(This changes the default settings for a number
of basic parameters).
6. Press [Main Menu] on the LCP.
Commissioning
VLT
®
HVAC Drive Operating Instructions
24 MG11AJ02 - Rev. 2013-07-31
55
- Operating Instructions 1
- HVAC Drive FC 102 1
- Contents 3
- 6 Application Set-up Examples 4
- 8 Specifications 4
- 9 Appendix 4
- 1 Introduction 5
- 2 Safety 7
- EQUIPMENT HAZARD! 8
- WINDMILLING! 8
- INTERNAL FAILURE! 8
- Type 12 / IP55 Tamb.45 9
- 3.1.3 Product Overview 10
- Mechanical Installation 11
- 130BD528.10 12
- 130BD504.10 12
- 4 Electrical Installation 13
- 4.4 Wiring Schematic 14
- EMC INTERFERENCE! 15
- 130BT248.10 16
- 130BT334.10 16
- 4.7 AC Mains Connection 17
- 4.8 Control Wiring 18
- Control Terminal Types 18
- 130BD546.10 19
- 130BD530.10 20
- 5 Commissioning 23
- 2605 kWh 24
- Basic Programming 26
- Asynchronous Motor Setup 27
- Permanent Magnet Motor Setup 27
- 5.5 Checking Motor Rotation 29
- 5.6 Local-control Test 29
- 5.7 System Start-up 29
- Maintenance 29
- 6.1 Application Examples 30
- 6.1.1 Speed 30
- Start/Stop 31
- Application Set-up Examples 32
- 6.1.4 RS-485 33
- Motor Thermistor 33
- 7.1 Status Messages 34
- 130BP086.11 36
- 36 MG11AJ02 - Rev. 2013-07-31 38
- MG11AJ02 - Rev. 2013-07-31 37 39
- MG11AJ02 - Rev. 2013-07-31 39 41
- 40 MG11AJ02 - Rev. 2013-07-31 42
- 7.4 Troubleshooting 43
- Specifications 46
- 8.2 Mains Supply 53
- 8.4 Ambient Conditions 53
- 52 MG11AJ02 - Rev. 2013-07-31 54
- MG11AJ02 - Rev. 2013-07-31 53 55
- 54 MG11AJ02 - Rev. 2013-07-31 56
- Connection Tightening Torques 57
- 8.8 Fuse Specifications 58
- 8.8.1 CE Compliance 58
- 380-480 V 59
- 525-600 V 59
- UL Compliance 60
- 3x525-600 V 62
- 3x525-690 V 63
- Appendix 66
- 68 MG11AJ02 - Rev. 2013-07-31 70
- MG11AJ02 - Rev. 2013-07-31 69 71
- 70 MG11AJ02 - Rev. 2013-07-31 72
- MG11AJ02 - Rev. 2013-07-31 71 73
- *MG11AJ02* 74
Manuais e produtos relacionados com Adaptadores e conversores de corrente Danfoss 102
(28 páginas)
(1 páginas)© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.056 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais