Danfoss TS715 Si Manual do Utilizador

TS715 SiInstallation & User Instructions(Including 24V models)Electronicsingle channel timeswitch ®Certification Mark

10DANFOSS RANDALLTS715-SiMAINSNLNLThe TS75/TS15 wallplate must be used to replace the existing wallplate when replacing thage systems, fi t wire link b

11LOADAn additional terminal block may be re-quired where these disconnected leadss (or pairs of leads) should be terminatedCOM OFF SPARE ON12 3 4 AB

12What is a programmer?What is a programmer?... an explanation for householders.Programmers allow you to set ‘On’ and ‘Off ’ time periods. Some models

13User InstructionsYour timeswitchThe TS715-Si allows you to switch your system on and off at times that suit you. You can programme up to 3 seperate

14Setting the correct Time and DayBefore you start This will reinstate the preset programmes and sets correct day and time.To fully reset the unit see

15Press DAY/HOL to display day and month. Use the + or - buttons to set the correct month (Jan = 1, Feb = 2 etc.).Press DAY/HOL to display day and m

16!Before you change the preset programmesYour installer will have set your unit to operate in one of the following modes: 5/2 day - one set of prog

17Programming the ON/OFF Times in 5/2 day modeDAY/HOL1. Press PROG once until SET ON TIME appears at the top of the display and MOTUWETHFR appears a

18DAY/HOLDAY/HOLDAY/HOL4. Press the DAY/HOL button once and SASU will appear at the bottom of the display. 5. To set the times required for SA and

191. Press PROG once until SET ON TIME appears at the top of the display. Note the current day is displayed. Press the DAY/HOL button until the requi

2INDEXIndexInstallation Product specifi cation 3 Installation 3-4 Wiring 4 DIL switch settings 5 Advanced Programming Options 5 Copy Function

20 Continue programming the rest of the week by pressing: a) NEXT ON/OFF button to move to the next setting, b) + or - buttons to amend the time,

21Programming heating & hot water system  24 hour mode1. Press PROG once until SET ON TIME appears at the top of the display. Use the + OR - but

22Running your Programme To run the programme: press the SELECT button. Each time you press the SELECT button the display will change between O

23+1HR = pressing this button when the unit is in AUTO or ALLDAY mode will cause the system to remain on for an extra hour. If it is pressed while t

24Holiday ProgrammeHoliday ModeTo automatically bring the heating back on when returning from holiday the TS715 Si has a built in holiday feature.Foll

25This is handled automatically. Should the installer have turned off Automatic Time Change then follow the instructions below.Open the fl ap on the fr

26Service Interval TimerService Interval Timer If the property is owned by a landlord he may, for gas safety reasons, have instructed the installer

27 RESET If it is necessary to fully reset the unit, including the date and time, follow the instructions below.1. Press and hold the +1HR and MAN bu

28Fault Check List Troubleshooting

29

3Please Note: This product should only be installed by a qualifi ed electrician or competent heating installer, and should be in accordance with the cu

30

31

32Danfoss Randall LtdAmpthill RoadBedfordMK42 9ERTel: 01234 364621Fax: 01234 219705Part No 38070v11s7-06 09/10Still having problems?Call your local

4 The wallplate must be securely mounted either directly to the wall using suitable wood screws or to a fl ush mounted 1-gang electrical accessory bo

5DIL switch settings and Advanced Programming OptionsNot UsedNot Used5/2 Day7 DaySw.1Sw.2Sw.3Sw.4Not UsedNot Used7 Day or 24 Hour24 HourTick the INSTA

6Copy Functions ExplainedThere are 3 possible copy functions available. These are; Standard Copy, Enhanced Copy, and AB copy. Copy functions are enabl

7Service Interval TimerThe TS715 Si is fi tted with an installer setback service interval timer. If this feature is required please contact our technic

8DANFOSS RANDALLTS715-SiMAINSNLNLThe existing wallplate may be used when replacing the following, but the wiring must bebetween L & COM terminals

9LOADAn additional terminal block may be re-quired where these disconnected leadss (or pairs of leads) should be terminatedCOM OFF SPARE ON12 3 4 AB C